PIC18F258T-I/SOG【PDF 36/116 页】IC MCU FLASH 16KX16 28SOIC

收藏本站

您好，
买卖IC网欢迎您。
请登录
免费注册

买卖IC网

Sheet目录3878

32页 33页 34页 35页 [36页]37页 38页 39页 40页

2009 Microchip Technology Inc.

Preliminary

DS41364D-page 287

PIC16F193X/LF193X

REGISTER 23-4:

SSPCON3: SSP CONTROL REGISTER 3

R-0/0

R/W-0/0

ACKTIM

PCIE

SCIE

BOEN

SDAHT

SBCDE

AHEN

DHEN

bit 7

bit 0

Legend:

R = Readable bit

W = Writable bit

U = Unimplemented bit, read as ‘0’

u = Bit is unchanged

x = Bit is unknown

-n/n = Value at POR and BOR/Value at all other Resets

‘1’ = Bit is set

‘0’ = Bit is cleared

bit 7

ACKTIM:

Acknowledge Time Status bit (I2C mode only)(3)

= Indicates the I2C bus is in an Acknowledge sequence, set on 8TH falling edge of SCL clock

= Not an Acknowledge sequence, cleared on 9TH rising edge of SCL clock

bit 6

PCIE

: Stop Condition Interrupt Enable bit (I2C mode only)

= Enable interrupt on detection of Stop condition

= Stop detection interrupts are disabled(2)

bit 5

SCIE

: Start Condition Interrupt Enable bit (I2C mode only)

= Enable interrupt on detection of Start or Restart conditions

= Start detection interrupts are disabled(2)

bit 4

BOEN:

Buffer Overwrite Enable bit

In SPI Slave mode:(1)

= SSPBUF updates every time that a new data byte is shifted in ignoring the BF bit

= If new byte is received with BF bit of the SSPSTAT register already set, SSPOV bit of the

SSPCON1 register is set, and the buffer is not updated

In I2C Master mode:

This bit is ignored.

In I2C Slave mode:

= SSPBUF is updated and ACK is generated for a received address/data byte, ignoring the state

of the SSPOV bit only if the BF bit = 0.

= SSPBUF is only updated when SSPOV is clear

bit 3

SDAHT:

SDA Hold Time Selection bit (I2C mode only)

= Minimum of 300 ns hold time on SDA after the falling edge of SCL

= Minimum of 100 ns hold time on SDA after the falling edge of SCL

bit 2

SBCDE:

Slave Mode Bus Collision Detect Enable bit (I2C Slave mode only)

If on the rising edge of SCL, SDA is sampled low when the module is outputting a high state, the BCLIF

bit of the PIR2 register is set, and bus goes idle

= Enable slave bus collision interrupts

= Slave bus collision interrupts are disabled

bit 1

AHEN:

Address Hold Enable bit (I2C Slave mode only)

= Following the 8th falling edge of SCL for a matching received address byte; CKP bit of the

SSPCON1 register will be cleared and the SCL will be held low.

= Address holding is disabled

bit 0

DHEN:

Data Hold Enable bit (I2C Slave mode only)

= Following the 8th falling edge of SCL for a received data byte; slave hardware clears the CKP bit

of the SSPCON1 register and SCL is held low.

= Data holding is disabled

Note 1:

For daisy-chained SPI operation; allows the user to ignore all but the last received byte. SSPOV is still set

when a new byte is received and BF = 1, but hardware continues to write the most recent byte to SSPBUF.

This bit has no effect in Slave modes that Start and Stop condition detection is explicitly listed as enabled.

The ACKTIM Status bit is only active when the AHEN bit or DHEN bit is set.

发布紧急采购，3分钟左右您将得到回复。

采购需求

(若只采购一条型号，填写一行即可)

*型号	*数量	厂商	批号	封装

添加更多采购

采购需求

发布成功！您可以继续发布采购。也可以进入我的后台，查看报价

发布成功！您可以继续发布采购。也可以进入我的后台，查看报价

我的联系方式